Water/oil repellent, soiling and graffiti protection for very low porous materials
ProtectGuard® MG is a highly effective ability protection product designed to protect low and very low porosity substrates. It resist to penetration by water, oil, grease, graffiti, weak acids (fruit juice, ketchup, etc.) as well as all types of soiling.
ProtectGuard® MG is an impregnation product and not a coating, treated materials remain permeable to air and water vapour. ProtectGuard® MG is colourless and does not change the appearance or composition of the treated material. In addition, it is UV-resistant and does not discolor with age.
ProtectGuard® MG can be used inside and outside on all vertical and horizontal surfaces. It is ideal for treating all low and very low porous materials: marble, granite, ceramic, polished and crystallised surfaces, stoneware porcelain and all smooth mineral substrates, especially low porosity silica-limestone materials.ProtectGuard® MG is used for new and renovated constructions.
  • Ready to use & effective for more than 10 years.
  • Protects against water, oily liquids and graffiti.
  • Anti-staining, anti-soiling & anti-graffiti property. 
  • Limits surface moss and lichen growth.
  • Prevents deterioration resulting from freeze-thaw cycle. 
  • Non film-forming, lets the surface breathe. 
  • Cost-effective, a small quantity of product is sufficient to protect a large surface. 
  • UV-resistant, does not discolour. Abrasion-resistant.
Apply using a brush or microfiber cloth.
Clean tools and equipment immediately after use with a solvent.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove greasy stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement. Surface preparation ensures good efficiency of the treatment.
  • Rinse carefully and wait until the surface is completely dry and free from any cleaner marks before applying ProtectGuard® MG.
  • Use neat, do not dilute.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • The treated surface should be impregnated in a single application. 
  • Let the product penetrate and dry (from 10 to 60 min. depending on the porosity and temperature of material).
  • Do not over apply the product; remove any excess with a clean cloth by swabbing before the product dries.
  • Drying time: 1 hour.
  • The surface must be protected for 24 hours from traffic and liquids (rain, grease…). 
  • The surface can be polished without abrasion after application of the treatment.
  • Optimum effectiveness obtained after 48 hours.
  • Physical state at 20°C: Liquid.
  • Appearence: Uncoloured.
  • Odour: Slight.
  • pH: Not applicable.
  • Density: 0.9 ± 0.02.
  • Solubility in water [vol/vol]: Non soluble.
  • Flash point [°C]: > 63°C.
  • VOCs: 430 g/l*.
  • Rating for VOC emissions into idoor air: B.
Coverage depends on the porosity of the material. 
The figures below should be used only as a general guideline: 8 to 20 m²/litre.
250 ml, 5 and 25 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
Stubborn dirt should be cleaned off with clean water or with Guard Cleaner® Eco Soiled Floors diluted with 50% water.
  • Never apply with a sprayer.
  • Always work in a well-ventilated space. If not, wear a protection mask (type: ABEK).
  • For best results, ProtectGuard® MG is used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with any other product.
  • Resistance to acids on calcareous materials (non cristallized marble...) is limited. It is necessary to eliminate quickly acids on these materials.
  • On certain materials, product may increase slightly the original colour (carry out a preliminary test).
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Physical Propeties/Chemical:
Chlorophyllin® based solution.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 81
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.266