Specialist
Solution
Product
Document
Picture
Graffiti cleaner special residual ghosts
GraffiGuard® 2010 is a cleaner that removes ink and paint stains and residues sometimes left after graffiti has been cleaned off by GraffiGuard® 2030 Ecological.
  • Removes graffiti ghosts and outlines.
  • Aqueous-phase product.
  • Nonflammable.
  • Easy to use.
  • Exterior.
Apply using a brush.

Clean tools and equipment immediately after use with water.
  • Apply neat, do not dilute.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • For optimum results wet the surface before applying GraffiGuard® 2010. 
  • Apply GraffiGuard® 2010 with a brush, then work over the surface with circular movements. 
  • Leave to act for around 2 to 10 minutes. 
  • Rinse off with copious amounts of low-pressure water as hot as possible (increase the pressure of the pressure washer).
  • Always thoroughly wet the surface beneath with water.
  • Repeat entire operation if necessary.
  • Rinse off with copious amounts of cold water to neutralise.
  • Physical state at 20°C: Liquid
  • Appearence: Amber 
  • Odour: Solvent
  • pH: 14 ± 1
  • Boiling point [°C]: Non measured
  • Density: 1.15 ± 0.02
  • Solubility in water [vol/vol]: Total
  • Flash point [°C]: Not applicable
The following values are for guidance only:
3 to 5 m2/litre
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 48 months following the production date when kept in the original unopened container.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: Wear protection clothing for the skin with long sleeves and resistant to solvents.
  • Eye protection: Wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
  • GraffiGuard® 2010 is a corrosive product. Skin contact with the product can cause burns. Wear rubber gloves, protective clothing and goggles.
  • Use with care on painted surfaces. Clean immediately after application.
  • Attacks zinc, aluminium and their alloys.
  • Do not apply in rain or very hot weather. Temperature of air and substrates between 5°C and 30°C.
  • Do not dilute or mix with another product.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet. 
Accessing: 98
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.426
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other