Specialist
Solution
Product
Document
Picture
ImperGuard® Premium is a high-performance water-repellent designed to protect porous walls, facades and roofs against damp...>>

High-performance water-repellent for all porous materials
High-performance water protection for all porous building materials.
ImperGuard® Premium is a high-performance water-repellent designed to protect porous walls, facades and roofs against damp. ImperGuard® Premium penetrates deep into the pores of materials to make them impermeable and therefore limit the negative effects caused by damp, water ingress, acid rain, erosion, icing/melting cycles, formation of moss and lichens, the appearance of efflorescence or saltpeter, etc.
 
ImperGuard® Premium is a non-film forming impregnation product, the material remains permeable to air and water vapour. Completely colourless after application, it does not change the appearance or the nature of the treated material (no risk of bleaching). It is also fully resistant to UV rays and does not yellow over time.
Used outside on porous façades and roofs. Ideal for all types of material: natural or reconstituted stone, concrete, plaster, brick, cement, terracotta or slate tiles etc.
  • Water-proofing agent providing in-depth protection to porous materials from penetration of rainwater and also avoids harmful effects due to seepage, acid rain, erosion, freeze/thaw cycle, formation of mosses and lichens, efflorescence etc.
  • Next generation impregnation product that does not produce films. It is colourless after application, it does not change the appearance nor the nature of the treated substrate. Very good U.V.-resistance, it does not turn yellow.
Apply with a low-power spray, roller or brush.
Clean tools and equipment used with water immediately after use.
Apply the product to a clean, dust-free, degreased and dry surface. To remove any black stains, pollution or soiling that invades the materials, use Guard® Wash Express
  • Use the product neat, do not dilute.
  • Shake the packaging well before use and carry out a preliminary test.
  • The substrate must be impregnated up to saturation in one or two “wet-on-wet” layers.
  • Do not overload the substrate, remove any excess after drying. For vertical surfaces, apply from bottom to top.
  • Drying protected: 24 hours.
  • Maximum effect reached after 7 days.
  • Physical state at 20°C: Liquid
  • Colour: Milky
  • Odour: Slight
  • pH: 8 ± 0.5
  • Boiling point [°C]: 100 °C
  • Density: 1.0 ± 0.02
  • Water solubility [vol/vol]: Total
  • Flash point [°C]: Not applicable
5 and 20 litres
  • Store in a dry place at a temperature between 5°C and 30°C.
  • Storage: 12 months from date of manufacture, in original packaging unopened.
 
Respects the environment and is ecological:
  • Without petroleum solvents
  • Non-hazardous and non-toxic.
  • Biodegradable by more than 90%*
  • VOC < 2 g/l*
  • Only treat surfaces previously cleaned of all atmospheric pollution and stains.
  • Do not dilute or mix with another product.
  • Do not apply to organic, metal or impermeable materials. Frames and windows must be protected. Accidental colouring and stains must be cleaned immediately with water.
  • On some materials, the product may slightly accentuate the colour. Always do a test on the substrate to be treated before applying.
  • In case of contact with glass materials, immediately rinse with water.
  • For a perfect application and effective protection, the product must stirred and used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply in rainy or very hot weather. Air temperature between 5°C and 30°C.
  • Respiratory protection: No breathing apparatus is required under normal conditions of use provided there is adequate ventilation.
  • Protection of hands: Wear chemical-resistant gloves.
  • Skin protection: No special clothing or skin protection is recommended under normal conditions of use.
  • Protection of eyes: If there is a risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or specialist.
Consumption
Consumption depends on the porosity of the material. The following figures are given for information: 6-10 m²/litre.
Chemical Nature
Aqueous emulsion based on Chlorophyllane®.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: [email protected]
Website: www.guardindustrie.com

NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: [email protected]
Website:
www.nanophamgroup.com
www.congnghenano.vn
www.bacsivatlieu.vn
www.guardindustrie.com.vn

Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 97
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.424
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other