Specialist
Solution
Product
Document
Picture
Water/oil-repellent and stain protection for UHPCs
  • ProtectGuard® WF Special Concrete is a water and oil repellent product designed to protect concrete and high performance concrete such as Ductal®. It protects against the main causes of deterioration such as water penetration, atmospheric pollution and grease-based stains. A surface treated with ProtectGuard® WF Special Concrete will be easier to care for and will be protected over time.
  • ProtectGuard® WF Special Concrete is an ecological, waterbased product (non toxic, petroleum solvent-free).
  • ProtectGuard® WF Special Concrete is an impregnation product: it allows the substrate to remain permeable to air and water vapour. It is abrasion resistant and UV-resistant and does not yellow.
ProtectGuard® WF Special Concrete is used indoors and outdoors to protect horizontal or vertical concrete and fiber reinforced high performance concrete such as Ductal®.
  • Protects against water and oily liquids.
  • Anti-staining, anti-dirt.
  • Limits dirt due to pollution from building up again.
  • Limits moss and lichen growth.
  • Prevents deterioration resulting from the freeze-thaw cycle.
  • Makes cleaning easier.
  • Non film-forming, lets the surface breathe.
  • UV-resistant, does not yellow.
  • Good resistance to abrasion and scratches.
  • Ready to use.
Apply with an applicator, an HVLP spray gun or an air assisted gun.

Clean tools and equipment immediately after use with water.
Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove greasy stains, efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
  • Use neat, do not dilute.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • ProtectGuard® WF Special Concrete is applied in 2 layers.
  • Apply the 1st layer to the surface.
  • Let the product penetrate and dry (from 15 to 30 minutes according to the material’s porosity and temperature) then apply the 2nd layer.
  • Do not over apply, eliminate any exceeding product before drying.
  • Drying time: 24 hours.
  • Optimum effectiveness obtained after 5 to 7 days.
  • Physical state at 20°C: Liquid.
  • Appearence: Milky.
  • Odour: None.
  • pH: 8.5 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.01 ± 0.01.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline: 6 to 10m²/litre for 2 layers.
2 and 5 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
  • Stubborn dirt should be cleaned off with clean water or with Guard® Cleaner Eco Soiled Floors diluted with 50% water.
  • Following traffic-induced wear, the protection and ‘wetlook’ can be regenerated by re-applying ProtectGuard® WF Special Concrete neat or diluted with 50% of water.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • Biodegradable > 80%*.
  • VOC < 35 g/l*.
  • Remove all atmospheric pollution-related dirt from all surfaces to be treated before starting the treatment.
  • For best results it is essential that ProtectGuard® WF Special Concrete is used when the temperature of the substrates is between 10°C and 30°C.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Do not mix with any other product.
  • In certain cases, the product can slightly the slipperiness of the surface.
  • Always carry out a preliminary test.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature
Acrylic and fluor in aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: +84 918 244 844
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 87
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.389
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other