Specialist
Solution
Product
Document
Picture
Water, oil, stain and dirt repellent high-performance wood protection
WoodGuard® Professional is a new-generation product for protecting bare or renovated wood. It penetrates deep into all the fibres of the wood to make the wood completely impermeable to water, grease and stains. WoodGuard® Professional protects the wood, enhances its durability and simplifies its maintenance.
Once applied, WoodGuard® Professional is a completely colourless product that does not alter the structure and natural appearance of the wood (its figure, grain, etc.). It is a non-film forming product that allows the wood to breathe. It does not peel, blister or yellow.
NOTE: The greying of wood is a natural phenomenon that can be slowed but not prevented by WoodGuard® Professional. To protect against UV light and greying, use a colour treatment from our WoodGuard® Color range.
WoodGuard® Professional can be applied indoors and outdoors to all bare wood, e.g. pine, spruce, Douglas fir, pressure-treated wood, etc. It is ideal for treating weatherboarding, fencing, window shutters, floors, decking, panelling, garden furniture, saunas...
  • Excellent protection against water, dirt and stains.
  • Significantly reduces moisture absorption.
  • Limits surface growth of moss and lichen.
  • Colourless after drying: preserves the natural appearance of the wood.
  • Does not yellow.
  • Non-film forming, allows the wood to breathe.
  • Easy to clean.
  • Ready to use and easy to apply.
Apply with a graining brush or roller.

Tools and equipment should be cleaned with water immediately after use.
  • New wood: apply the product to wood that is clean, dustfree, sound and dry.
  • Resinous or greyed wood: clean with WoodGuard® Revitalizer, rinse thoroughly, clean off all dust and dry the wood.
  • Damaged wood: sand down to bare wood, clean off all dust and dry the wood.
  • Always prepare wood according to the current applicable codes of practice.
  • Ensure substrate has all the characteristics required for longevity.
  • The WoodGuard® and WoodGuard® Color ranges cannot prevent the wood from splitting if it is exposed to excessive variations of hygrometry. It is therefore recommended to apply our products when the wood has reached a low hygroscopic equilibrium. This condition can be measured easily because it occurs when the timbers have shrunk to their narrowest width, often less than the original width.
  • Use the product neat: do not dilute.
  • Shake the product well before use.
  • Do not apply during rain or in very hot weather. Ideal surface and air temperature 5°C to 30°C.
  • Test first on a small incospicuous area in the expected conditions and allow to dry for 24 hrs, particularly on resinous wood and exotic wood. Check the result by wetting the substrate.
  • Apply in the direction of the wood grain and if possible on all visible surfaces.
  • The substrate must be impregnated with two wet-on-wet layers until saturated.
  • Apply sparingly, removing all excess with a rag.
  • Protect from rain for 24 hrs and from oily deposits for at least 48 hrs.
  • Optimal performance is attained after 5 to 7 days.
  • Physical state at 20°C: Liquid.
  • Colour: Milky.
  • Odour: None.
  • pH: 8 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Relative density: 1.01 ± 0.005.
  • Solubility in water [vol/vol]: Total.
  • Flashpoint [°C]: Not applicable.
Coverage depends on how porous the wood is. The following values are for guidance only: 145 to 170 g/m2 for 2 layers.
5 litres.
  • Store in a dry place at a temperature of between 5°C and 30°C.
  • Shelf-life: 24 months from date of manufacture, in original unopened can.
  • Household stains can be sponged off with a pH-neutral household detergent.
  • A maintenance layer is recommended. This depends on the exposure and on the wood. The layer must be applied before the product suffers any deterioration.
Ecological and respects the environment:
  • Water-based product.
  • No petroleum-based solvents. 
  • Silicone-free.
  • Safe and non-toxic.
  • More than 80% biodegradable*.
  • VOCs < 60 g/l*.
  • Breathing protection: No breathing protection equipment is required under normal use conditions with suitable ventilation.
  • Hand protection: Wear latex gloves.
  • Skin protection: No skin protection or special clothing is recommended under normal use conditions.
  • Eye protection: If there is a significant risk of splashes, wear protective goggles.
  • In case of ingestion: Do not induce vomiting. Contact a doctor or specialist.
KEEP OUT OF REACH OF CHILDREN
Limitations on use
The treatment may be ineffective in the following cases:
  • On varnished, waxed, heat treated, polished, highly brushed, retified, modified or THT (high temperature treatment) woods.
  • On damp wood (moisture content > 16%).
  • Where micro-organisms or insects are present (pretreatment necessary).
  • Application, preparation and substrate not according to current French codes of practice DTU 59.1 (Paintwork), 42 (Weatherboarding), 36.1 (Woodwork), etc.
  • On sapwood.
  • Untested application on exotic or resinous wood.
  • On wood that has undergone a fire-resistance treatment.
  • On sharp edges (sharp edges should preferably be rounded to ensure continuity of product and thus avoid breaks in coverage).
  • Ends, cuts, drill holes, etc. not saturated with product.
Chemical nature
Fluorinated acrylic copolymer.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: +84 918 244 844
Website: 
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 88
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.363
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other