Specialist
Solution
Product
Document
Picture
 Two-component protection, decoration, art and waterproofing, anti-oil, anti-stain, anti-graffiti, anti-rust, anti-corrosion...
For grp, grc, concrete, plastic, paint, metal...
Nano Protect Color NPG® is a newgeneration product for the protection, decoration, art and waterproofing, anti-oil, anti-stain, anti-graffiti, anti- rust, anti-corrosion... for GRP, GRC, concrete, plastic, paint, metal...
Nano Protect Color NPG® is a two-component product, that provides to give it lasting protection against graffiti and tags of all kinds (paint, felt pen...), water, grease and stains.
Nano Protect Color NPG® protects treated surfaces permanently. It can be cleaned dozens of times (using GraffiGuard® 2010 anti-graffiti cleaner) and will still keep working, so it does not need to be reapplied after graffiti has been removed.
Nano Protect Color NPG® is not a paint but a semi-transparent impregnating that does not alter the structure or appearance of the GRP, GRC, concrete, plastic, paint, metal...
Nano Protect Color NPG® does not peel, blister or yellow. It slows the aging of GRP, GRC, concrete, plastic, paint, metal... simplifies its maintenance and allows its new, clean appearance to be preserved for much longer.
Nano Protect Color NPG® can be applied indoors and outdoors to protect, decoration, art and waterproofing, anti-oil, anti-stain, anti-graffiti, anti-rust, anti-corrosion... for GRP, GRC, concrete, plastic, paint, metal...
  • Unlike a paint, it colours.
  • It is a new-generation product for the protection, decoration, art and waterproofing, anti-oil, anti-stain, anti-graffiti, anti-rust, anti-corrosion... for GRP, GRC, concrete, plastic, paint, metal...
  • Abrasion and scratch resistant.
  • Limits surface growth of moss and lichen.
  • Easy to clean.
  • Other features.
Applying the 1st layer: 
  • Apply Nano Protect Color NPG® diluted with not more than 5 to 10% water. Mix thoroughly. The first layer must be regarded as a primer layer designed to both impregnate the GRP, GRC, concrete, plastic, paint, metal... and provide a key for the next layer.
  • Apply sparingly to avoid producing a thick film.
  • Leave to dry for 30 min to 1 hour at 20° C. The substrate must be dry and non-tacky before it can be reworked (maximum time between 2 coats: 24h).
  • For best results rub down before the second layer.
Applying the 2nd layer:
  • Apply the second layer sparingly using undiluted Nano Protect Color NPG®.
  • If a third layer is needed, repeat the procedure described above. Wait until completely dry before applying any additional layer to reach the optimal coverage.
  • Protect from rain for 24 hours and from oily deposits for at least 48 hours.
  • Optimal performance is attained after 5 to 7 days. 
For better control and best final results, Nano Protect Color NPG® should preferably be applied with an air-assisted spray gun. Brush application is also possible.
Tools and equipment should be cleaned with water immediately after use.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove stains and greasy stains use Guard Cleaner® Eco Soiled Floors. Rinse carefully and wait until the surface is completely free from any cleaner marks before applying the protection.
  • The surface must be cohesive. Do not apply to GRP, GRC, concrete, plastic, paint, metal... if any treatment has been applied after demolding.
  • Do not apply during rain or in very hot weather. Ideal surface and air temperature 10°C to 30°C.
  • Test first on a small inconspicuous area and allow to dry for 24 hrs. Check adhesion.
  • Shake product A (base) thoroughly before use.
  • Add part B (hardener) slowly to part A (base) of Nano Protect Color NPG®, stirring continuously. Use an electric stirrer to stir at medium speed until the mixture is homogeneous (around 5 to 15 minutes depending on quantity).
  • Leave the mixture exposed to the air for 15 to 30 min to allow bubbles to escape, then stir again for 1 min before use.
  • The resulting mixture can be used for 4 hours if the ambient temperature is below 25°C. If the temperature is higher, the useable time will be shorter. Do not use the mixture after this time.
  • Physical state at 20°C: Liquid.
  • Colour: Coloured.
  • Odour: None.
  • pH: 7 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Relative density: About 1.06 depending on the colour.
  • Solubility in water [vol/vol]: Total.
  • Flashpoint [°C]: Not applicable.
Coverage depends on how porous the GRP, GRC, concrete, plastic, paint, metal... is. The following values are for guidance only: 100 to 200 g/m² for 2 layers. 
5 litres kits. Product A (base) + product B (hardener).
  • Store in a dry place at a temperature of between 5°C and 30°C.
  • Shelf-life: 12 months from date of manufacture, in original unopened can.
  • Rinse regularly with clear water.
  • In case of remaining stain, use Guard Cleaner Eco Soiled Floors (diluted 1 : 9) and a smooth sponge if necessary.
  • Graffiti (paint, ink) can be cleaned off with a rag soaked in GraffiGuard® 2010. Always rinse off with plenty of clean water immediately afterwards. Always test a small area first.
  • As with any pigmented finish for exterior use, the colour will change over time. Differences in shades may therefore develop between areas exposed to UV radiation (sun and moon) and areas sheltered from this radiation (northfacing or shaded). The architectural design therefore has an influence on the overall finish of a project. A maintenance layer is recommended. This layer must be applied before the product suffers any deterioration.
Ecological and respects the environment:
  • Water-based product.
  • No petroleum-based solvents.
  • Silicone-free.
  • Safe and non-toxic.
  • More than 80% biodegradable*.
  • VOCs < 30 g/l*.
  • Breathing protection: Wear a protective mask (type P3).
  • Hand protection: Wear latex gloves.
  • Skin protection: Wear skin protection or special clothing.
  • Eye protection: Wear protective goggles.
  • In case of ingestion: Do not induce vomiting. Contact a doctor or specialist.
PROFESSIONAL PRODUCT
Chemical nature
Two-component fluorinated polyurethane with mineral pigments (Nano technology).
Available colours
Nano Protect Color NPG® stains come in 42 standard colors and are available in flat or glossy finish. Customers’ own colours can also be incorporated in the laboratory or on site on demand.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 87
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
Total online: 1.665.370
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other